返回 产品详情
单份组自干金属免烘烤油墨
来自凯贤实业(上海)有限公司
¥200.00
发布时间  2022-03-07 12:37:13 关注次数  560
凯贤实业(上海)有限公司
免费会员 3年
商家供应
图文介绍 产品参数 供应商信息


欧莱斯MPB烤漆面金属油墨

本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板等制品的丝印及移印。
油墨特性:
1、平光、附着力佳、耐汽油、耐化学品;
2、手感好,流平性佳、面光洁;
3、表面硬度好,耐冲击性能强、抗刮伤;
4、耐汽油、耐酒精、耐化学品程度佳;
印刷:选用网目为100-350目,以120T网纱计算涂覆盖面积每公斤达30~35㎡。
表干时间自然挥发5-15分钟,实干时间在24小时以内,48小时后达性能。
1.用配套专用稀释剂开油水
2.用718洗网水洗网。
3.或添加配套硬化剂10%可增加附着力,提高墨膜硬度。
4.烤箱80℃烘烤10分钟佳能更优。
测试方法(完全干燥后):
1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。
使用方法:
1.建议用我公司专用稀释剂进行稀释,不建议使用783慢干稀释剂稀释,使用前应充分搅拌,用后随时密封。
2.搅拌时加本公司配套开油水10-12%,稀释到印刷适合粘度,移印稀释使用移印专用稀释剂;用718洗网水清洗。
3.不得与其它类型油墨混合使用,否则容易出现其他附着力,化学反应等不良现象。
4. 加入固化剂的油墨使用时限为8小时,过期请弃用,剩余油墨不可回收
注意事项:
1.各种承印物料的外观相似,但可能会是不同的材料,客户需先试印,确其符合要求后,再批量生产。
2.在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3.环境温度过高,将会影响油墨原有质量。白色超越150都会变色,烘烤时请用木质材料垫底进行烘烤,不得直接接触铁
4.根据气候变化,请远离火源,阴暗处15度-30度环境下存放
Brand: but MY name: anodic oxidation INK Numbers: 65496
Anodic oxidation ink series
The product is produced with advanced import acrylic resin and senior pigment after fine grinding system, used in combination to ABS, PP, PET, all kinds of bbbbl, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface and roast (spray paint products of screen and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion.
Ink characteristics:
1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals;
2, feel is good, flow ping sex, good surface is bright and clean;
3 and fine surface hardness, impact resistance properties of strong, resistance to scratch;
4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good;
Printing:
Choose for 100-350 mesh mesh to 120 T nets yarn with coverage area calculation per kilogram of 30 to 35 ㎡.
Dry time table natural volatilize 5 to 15 minutes, bbbbbb in time within 24 hours, after 48 hours of optimum perbbbbance.
1. With matching special thinner, open oil and water
2. Wash washing nets with 718 net.
3. Or add hardener 10% supporting can increase adhesion, improve ink film hardness.
4. Preheat the oven to 80 ℃ bake for 10 minutes Canon even better.
Test bbbbbb (dry) :
1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up not to take off oil.
2. The purity of 99% alcohol 500 G force in ink surface wipe 300 times back and forth without decoloring.
bbbbbb of use:
1. The proposal with my company special thinner to dilute, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing.
2. Add the company supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718.
3. Not with other kinds of printing ink mixed use, otherwise easy to have other adhesion, chemical rebbbbbbs and other bad phenomenon.
4. Add hardener inks use time limit for 8 hours, please not used, the remaining expired ink not recycling
Note:
1. All kinds of printing material appearance similar, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production.
2. In moving printing process, such as a wire drawing or away, can be appropriabbby to add some slow dry paste can;
3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron
4. According to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for

品牌欧莱斯
型号mpl-a-1005
细度10um
粘度1000ps
用途金属
等级二等级
成份80%
耐温性超强
着色力100%
执行标准德标
加工定制
是否进口
存储条件干燥
保质期24个月
包装桶装
颜色可调
产地上海
凯贤实业(上海)有限公司
  • 公司类型私营有限责任公司
  • 经营模式贸易公司-私营有限责任公司
  • 联系人黄木
  • 联系手机18486349626
  • 联系固话021-59507952
  • 公司地址上海市嘉定区外冈工业园638号南门
主营业务
塑料丝印油墨,金属丝印油墨,陶瓷丝印油墨
凯贤实业(上海)有限公司成立于2009年,本公司致力于UV油墨、丝网油墨、移印油墨的经销与贸易!经营“欧莱斯”品牌油墨。 本着以客户为本的原则.提出以“效率就是金钱”“质量就是生命”的宗旨,兢兢业业为广大客户提供优质的产品品,合理的价格及良好的售后服务。。 我司油墨产品如下: SPPD系列油墨:针对PP,PE,BOPP,HIPS等塑料具有良好的稳定性,附着性、具有耐酒精、耐磨擦、耐百格等特性。 MPL系列油墨:主要针对各种金属,玻璃,陶瓷,电镀,不锈钢,铝合金,氧化铝,尼龙加玻纤,五金涂层等等具有自干稳定性强,附着力佳,色泽鲜艳等特性。 SP系列油墨:主要针对各种ABS,PS,PC,AS,PMMA等材料,具有耐酒精,耐磨擦,耐汽油,耐正己烷,丝印移印通用,高稳定,高附着力等特性。 TPE系列橡胶漆油墨,大理石油墨、密胺餐具油墨、镜面银镜面金油墨等等。 SP、SPP、PET、MPL系列溶剂型丝网油墨: 丝印、移印通用,高附着力,适用于PC/ABS/PS,PP/PE,PET,及其各种金属等材料,应用于电脑,手机,笔类、文件夹,金属铭牌,各类硬质金属,塑胶及金属电镀层等。
黄木 电话咨询 立即询价