免费会员
进入店铺
店铺留言
深圳市宝力晟电池有限公司生产的低温18650锂电池已通过GJB4477-2002标准，零下40°C低温放电容量保持率达到了84%。
如需批量采购请电联或者加微洽谈！
CUSTOMER NO：
ShenZhen BLS Battery Co., Ltd
深圳市宝力晟电池有限公司
-40℃ Low Temperature Li-ion Battery
Specification Approval Sheet
-40℃低温锂离子蓄电池规格确认书
MODEL/型号：BS18650/2200mAh
（2200mAh 3.7V）
Prepared By/Date
编制/日期
Checked By/Date
审核/日期
Approved By/Date
批准/日期
2018.10.12
Customer
Approval
客户确认
Signature/签字
Date/日期
Company Name
公司名称
Company Stamp
公司印章
Amendment Records/修正记录
Revision
版本
Debbbbbbion
记述
Prepared by
编制
Approved by
批准
Date
日期
A
陈红军
万 斌
Content/目录
P4
1 Scope/适用范围
P4
2 Model/型号
P4
3 Cell Specification/电芯规格说明
P5
4 Battery/Cell perbbbbance test Criteria/电池性能标准
P5
4.1 Appearance inspection by visual/外观目测
P5
4.2 Environmental test condition/外界环境条件
P5
4.3 Electrical characteristics/电气特性
P6
4.4 Mechanical characteristics/机械特性
P6
4.5 Safety perbbbbance/安全性能
P7
5 Cell initial Dimensions/电芯初始尺寸
P7
6 CAUTIONS IN USE（谨慎使用）
P8
7 Period of Warranty/保质期
P8
8 Storage of the Batteries/电池的存放
P8
9 Other The Chemical Rebbbbbb/其它化学反应
This specification is applies to describe the related Battery product in this Specification and the Battery/cell supplied by ShenZhen BLS Battery Co., Ltd only.
本说明书只适用于描述本规格书中相关的产品以及深圳市宝力晟电池有限公司提供的电池。
2 Model/型号：BS18650-2200mAh
3 Cell Specification/电芯规格说明
No.
Items / 项目
Specifications / 规格
Remark / 备注
1
Nominal Capacity
标称容量
2200mAh
0.2C Standard discharge
0.2C 标准放电
（Within 30 days from Factory）
（在出厂30天内）
2
Minimum Capacity
最小容量
2150mAh
3
Nominal Voltage
标称电压
3.7V
Mean Operation Voltage
即工作电压
4
Delivery voltage
交货电压
≥3.6V
Within 10 days from Factory
在出厂10天内
5
Charge Voltage
充电电压
4.2V±0.03V
By standard charge bbbbbb
标准充电方式
6
Standard charging bbbbbb
标准充电方式
0.2C constant current，4.2V constant voltage charge to 4.2V，continue charging till current decline to≤0.01C
0.2C恒流4.2V恒压充至电流≤0.01C，
时间约7h（供参考）
7
Charge current
充电电流
0.2C
440mA
Standard charge, charge time about 7h（Ref）
标准充电，时间约7h（供参考）
0.3C
660mA
Rapid Charge, charge time about： 5h（Ref）
快速充电，时间约5h（供参考）
8
Standard discharging bbbbbb
标准放电方式
0.2C constant current discharge to 3.0V，
0.2C恒流放电至3.0V
9
Cell Internal Impedance
单电芯内阻
≤45mΩ
Internal resistance measured at AC 1KHZ after 50% charge
半电态下用交流法测量内阻
10
Maximum charge current
最大充电持续电流
1C
2200mA
For continuous charging mod
连续充电模式
11
Maximum discharge current
最大放电持续电流
2C
4400mA
For continuous discharge mod（Discharge capacity for more than 80% of the nominal capacity）
连续放电模式（放电容量为标称容量的80%以上）
12
Operation Temperature and relative humidity Range
工作温度和湿度范围
Charge/充电
-20℃~45℃
60±25%R.H.
Charge at a very low temperature such as blew 0℃，will be get a lower capacity and reduce cycle life of the battery
低温充电效率会下降，会影响电池使用寿命
Discharge/放电
-40~60℃
60±25%R.H.
13
Storage temperature for a long time
长时间储存温度
-20~25℃
60±25%R.H.
Do not storage exceed half year. Must charge once when storage for half year. must charge the battery which with protect circuit when storage for three months.
不可超过半年，达到半年须充电一次
带保护板电池3个月充电一次
4 Battery/Cell perbbbbance test Criteria/电池性能标准
4.1 Appearance inspection by visual/外观目测
There shall be no such defect as rust, leakage, which may adversely affect commercial Value of battery.
电池外观应没有锈渍、污渍、漏液等影响商业价值的缺陷存在。
4.2 Environmental test condition/外界环境条件
Unless otherwise specified, all test stated in this product specification are conduct at below test condition
所有测试应按以下环境条件进行，除非特殊指定外。
Temperature：20℃~25℃
Relative Humidity：60%±25% R.H.
4.3 Cell Electrical characteristics/电气特性
No
Items/项目
Test bbbbbb and Condition/测试方法及条件
Criteria/标准
1
Rated Capacity at 0.2C（Min.）
0.2C最小额定容量
After standard charge, the capacity shall be measured on 0.2C discharge till the voltage discharge to3.0V，
标准充电后，放电至3.0V，截止，测量0.2C放电容量
≥2150
mAh
≥100%
Rated Capacity at 0.5C（Min.）
0.5C最小额定容量
After standard charge, the capacity shall be measured on 0.5C discharge till the voltage discharge to 3.0V，
标准充电后，放电至3.0V截止，测量0.5C放电容量
≥2086
mAh
≥97%
Rated Capacity at
1C（Min.）
1C最小额定容量
After standard charge, the capacity shall be measured on 1C discharge till the voltage discharge to 3.0V，
标准充电后，放电至3.0V 截止，测量1C放电容量
≥2090
mAh
≥95%
2
Cycle Life
循环寿命
Charging and discharging battery as blew conditions
0.2C standard charge to 4.2V end-off
0.2C standard discharge to 3.0V cut-off
Continuous charge and discharge for 300 cycles ，the capacity will be measure after the 300th cycle
充放电按以下条件：
0.2C标准充电至4.2V，0.2C标准放电至3.0V，连续充放电循环300周，在第300周结束后测量容量
≥80% of initial capacity
3
Capacity retention
容量保持
The battery to be charge in accordance with standard charge condition at 20~25℃，then storage the battery at an ambient temperature 20~25℃ for 28 days.
Measure the capacity after 30 days with 0.2C at 20~25℃ as retention capacity
将电池在20~25℃标准充电后储存在20~25℃的环境中28天
28天后，测试电池在20~25℃环境下0.2C放电容量作为保持容量
Retention capacity
容量保持
≥85%
Temperature Dependence of discharge capacity
（放电温度特性）
Cells shall be charged per 3.3.1 and discharged @0.2 C5A to 2.5 volts. Except to be discharged at temperatures per Table 3. Cells shall be stored for 3 hours at the test temperature prior to discharging and then shall be discharged at the test temperature. The capacity of a cell at each temperature shall be compared to the capacity achieved at 23 ºC and the percentage shall be calculated.
电池按3.3.1规定充电。按表3的温度中放电，电池必须先在该试验温度中放置3个小时。
Each cell shall meet or exceed the requirements of Table 3
温度中的放电容量应不小于表3的要求
Table 3 （表3）
Discharge Temperature
（放电温度）
-40℃
-20℃
0℃
23℃
60℃
Discharge Capacity（0.2 C5A）
（放电容量/0.2 C5A）
82%
85%
90%
100%
85%
4.4 Mechanical characteristics/机械特性
No
Items/项目
Test bbbbbb and Condition/测试方法及条件
Criteria/标准
1
Free fall test
自由跌落测试
The battery to be fully charged in accordance with standard charge condition, then drop the battery three times from a height of 1,0 m onto a concrete floor. The batteries are dropped so as to obtain impacts in random orientations.
电池按照标准充电条件充满电，然后从1m高度跌落电池到一个水泥地面，随机跌落三次。
No Fire,
不起火，不
2
Vibration test
振动测试
After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz and 55Hz, the excursion of the vibration is 1.6mm. The cell shall be vibrated for 30 minutes per axis of XYZ axes.
将标准充电后的电芯固定在振动台上，沿X、Y、Z三个方向各振动30分钟，振幅1.6mm，振动频率为10Hz~55Hz，每分钟变化1Hz。
No explosion, No leakage, No fire
无泄漏，不起火，不
No
Items/项目
Test bbbbbb and Condition/测试方法及条件
Criteria/标准
1
Thermal exposure test
高温热冲击测试
Each fully charged cell, stabilized at room temperature, is placed in a circulating air-convection oven. The oven temperature is raised at a rate of 5℃/min ± 2℃/min to a temperature of 130℃ ± 2℃. The cell remains at this temperature for 10 min before the test is discontinued.
充满电的电池温度稳定到常温后，放置入循环空气烘箱里，从常温以5℃/分±2℃/分的速率升至130℃后，在130℃放置10分钟
No explosion, No fire
无起火，无
2
Short test
短路测试（20℃）
The fully charged battery is to be short-circuited by connecting the positive and negative terminals of the battery with resistance load not exceed 100mΩ.Tests are to be conducted at room temperature 20~25℃.
在室温20~25℃把充满电的电池的正负极用不超过100mΩ的负载连接起来，连接起来使电池外部短路
No explosion, No fire
The Temperature of the Battery surface not exceeded than 150℃
无起火，无
电池表面温度不超过150℃
3
Short test
短路测试（60℃）
The fully charged battery is to be short-circuited by connecting the positive and negative terminals of the battery with resistance load not exceed 100mΩ.Tests are to be conducted at room temperature about 60-65℃
在室温约为60-65℃把充满电的电池的正负极用不超过100mΩ的负载连接起来，连接起来使电池外部短路
No explosion, No fire
The Temperature of the Battery surface not exceeded than 150℃
无起火，无
电池表面温度不超过150℃
4
Forced discharge test
过放电测试
A discharged cell is subjected to a reverse charge at 1C for 90 min.
将电芯放完电，再用1C反接充电90分钟
No explosion, No fire
无起火，无
5
Over charge test
过充电测试
After standard charge, continue to charge with a constant voltage 1C charge till the voltage charge to 6.0V .
电芯标准充满电后，以1C电流充电直至电压到6V即停止，
No explosion, No fire，
无，无起火
5 Cell initial Dimensions/电芯初始尺寸
NO
Items
Units：mm
1
diameter/直径（D）
18.2.±0.30
3
Height/高度（H）
65.0±0.50
Draw/制图
Checked/审核
Approved/批准
陈红军
6 CAUTIONS IN USE（谨慎使用）
To ensure proper use of the battery please read the manual carefully before using it.
（为确保正确使用电池，使用前请仔细阅读本细则）
Handling（电池操作）
l Do not expose to, dispose of the battery in fire.（不要靠近和放置电池于火中）
l Do not put the battery in a charger or equipment with wrong terminals connected.
（在充电器或设备仪器中不要把电池接错电极）
l Avoid shorting the battery（避免电池短路）
l Avoid excessive physical shock or vibration.（避免电池过多的物理撞击和震动）
l Do not disassemble or debbbb the battery.（不要解剖和使电池变形）
l Do not immerse in water.（不要把电池浸泡在水中）
l Do not use the battery mixed with other different make, type, or model batteries.
（不要和其它不同类型的电池混和使用）
l Keep out of the reach of children.（放置电池于儿童不易接触的地方）
charge and discharge（充电和放电）
l Battery must be charged in appropriate charger only.（电池必须用适当的充电器充电）
l Never use a modified or damaged charger.（不要使用改装或损坏的充电器）
l Do not leave battery in charger over 24 hours.（不要把电池放置于充电器超过24h）
storage（储存）
l Store the battery in a cool, dry and well-ventilated area.
（应把电池置于凉爽、干燥及通风良好的区域）
disposal（电池处理）
l Regulations vary for different countries. Dispose of in accordance with local regulations.
（电池处理要符合当地的规定）
7 Period of Warranty/保质期
The period of warranty is one year from the date of shipment. Great Power guarantees to give a replacement in case of cells with defects proven due to manufacturing process instead of the customer abuse and misuse.
电池的保质期从出货之日算起为一年。如果电池的缺陷是在制造过程中形成的而不是由于用户滥用及错误使用造成，本公司负责退换电池。
8 Storage of the Batteries/电池的存放
The batteries should be stored at room temperature, charged to about 60% to 80% of capacity.
We recommend that batteries be charged about once 3 months to prevent over discharge.
电池应当在室温下存放，应充到60%至80%的电量。如长时间储存，建议每3个月充一次电以防止电池过放电。
9 Other The Chemical Rebbbbbb/其它化学反应
Because batteries utilize a chemical rebbbbbb, battery perbbbbance will deteriorate over time even if stored for a long period of time without being used. In addition, if the various usage conditions such as charge, discharge, ambient temperature, etc. are not maintained within the specified ranges the life expectancy of the battery may be shortened or the device in which the battery is used may be damaged by electrolyte leakage. If the batteries cannot maintain a charge for long periods of time, even when they are charged correctly, this may indicate it is time to change the battery.
由于电池是利用化学反应的原理，所以随时间的增加电池的性能会降低，即使是存放很长一段时间而不使用。如果使用条件如充电、放电及周围环境温度等情形不在指定的使用范围内，会使缩短电池的使用寿命，或者会产生漏液导致设备损坏。如果电池长周期不能充电，即使充电方法正确，这样需要更换电池了。
10 Note/注释
Any other items which are not covered in this specification shall be agreed by both parties.
本说明书未包括事项应由双方协议确定。
*声明：本规格书信息仅仅是对产品性能的简述，并不意味着是对任意一只电池做出的担保。电池的相关参数可以在未通知的情况下自主进行修改，请及时与宝力晟保持联系以取得最新资料信息。
1 Scope/适用范围
2018 BLS Battery co., Ltd. All rights reserved. BLS Battery co., Ltd. attempts to ensure the correctness of the product debbbbbbion and data contained herein. We reserve the right to change designs, specifications and pricing at any time without notice or obligation. It is the responsibility of the reader of this inbbbbation to verify any and all inbbbbation presented herein.
- 公司类型私营独资企业
- 经营模式生产加工-私营独资企业
- 联系人胡工
- 联系手机13424333184
- 联系固话0755-29498929
- 公司地址深圳市宝安区福永街道
-
602540 802540聚合物锂电池3.7V600mAh无线鼠标消毒灯蜡烛灯电池 ¥6.50 -
603759聚合物锂电池1500mAh导航仪可视门铃空气净化器感应灯电池 ¥10.00 -
552535 602335方形软包3.7V500mah补水仪喷雾仪报警器聚合物锂电池厂家 ¥7.00 -
602035聚合物电池生产厂家3.7V400mAh蓝牙耳机消毒盒补水仪充电电池 ¥5.70 -
颢明103040软包3.7v1200mah按摩器对讲机高温聚合物锂电池 ¥8.50 -
颢明103048纯三元软包锂电池3.7V1500mAh按摩器补水仪电池 ¥9.00 -
颢明601235三元锂电池3.7V200mAh电子计力器 电子握力计电池 ¥2.40 -
颢明553035聚合物锂电池3.7V600mAh监护仪蓝牙耳机充电仓MP3电池 ¥4.00 -
颢明802040小聚合物锂电池3.7V650mAh扫码器探测器VR眼镜电池 ¥6.50 -
颢明80度放电804980耐高温锂电池3.7V4300mAh共享单车导航仪电池 ¥24.00 -
颢明4025130长条形聚合物锂电池3.7V1500mAh橱柜灯LED灯具电池 ¥7.00 -
颢明3844105黑皮聚合物锂电池高压3.8V2650mAh智能手机电池 ¥13.00 -
英国HAWKER霍克AGVSafe磷酸铁锂电池EV24-40 24V40Ah支持RS485 ¥452.00 -
英国HAWKER霍克锂电池EV24-60 24V60AH 磷酸铁铅酸蓄电池持续消耗 ¥4704.00
-
INSPIRED ENERGY锂电池NB3037HD25 美国进口全新 ¥996.00
