我要找液下渣浆泵过流A沽源液下渣浆泵过流

3，液下泵关闭出口管路阀门及压力表。4，液下泵起动电想法，以压力表指示敞开出口阀门到需要位置。5，液下泵正常泊车，该领先关闭出口阀门，然后间断电想法，关闭压力表。6，液下泵轴承室应包管满足的油脂，轴承温升不得高于70℃。三 液下泵的设备需要1，锅炉给水泵泵必需笔直设备在液料池或水槽上面的固定支架上。2，液下泵泵的吸进口距离池底部应大于200㎜。3，液下泵泵的出口管路必需另设支架，不容许将其重量直接落在泵体上。​。

一、产品概述SP液下渣浆泵为立式离心液下渣浆泵，浸入液下，用于输送磨蚀性、粗颗粒、高浓度渣浆。不需要任何轴封和轴封水，在吸入量不足的工况下也能正常工作。

SP型液下渣浆泵过流部件由耐磨金属制成。 

根据渣浆池液面的高低，可选择不同长度的泵传动轴或吸入管。 

采用多种速度和多种变型方式，使得泵在最佳工况下运行，使用寿命长，运行效益高，能满足多类恶劣的输送条件。 

Second, SP liquid slurry pump application Range 
Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in bbbbllurgy, mining, coal, electricity, building materials, environmental protection and other departments.
Third, SP liquid slag slurry pump structure debbbbbbion 
The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.

我要找液下渣浆泵过流A沽源液下渣浆泵过流

3， 扬程裕量渣浆泵在运转过程中，由于过流部件的磨损泵性能不断下降，直至最终不能满足工况要求。为使泵能长时间的运转在额定工况附近，通常在选泵时增加一个扬程裕量。一般裕量取额定扬程的10%。4， 过流部件材质的选择。

五、型号意义

    40 PV-SP

   40----------吐出口径40mm

   PV--------- PV型轴承组件

   SP----------液下泵

水泵安装

 泵安装的好坏对泵的运行和寿命冇重要影响，所以安装和校正必须仔细进行。泵的外形及安装尺寸。